Tumble Dryer Heater Element Assembly - 2300W Stock Number: ES1073664
High quality spare part for select models of Hotpoint, Indesit and Proline tumble dryers
Manufactured by Hotpoint
(This part fits select models)
Will this part fit my Appliance?
Check this part fits your appliance
High Quality Replacement Tumble Dryer Heater Element Assembly - 2300W
If your clothes are still cold and damp after a cycle in your tumble dryer and you can identify that it is the heating element to blame, this replacement set that includes a thermostat that could help you get your dryer back in working order. You will soon be back to dry clothes again in no time!
Specification:
- 2300 Watts
- Includes: Thermostat
Compatiable spare part for select models of Hotpoint, Indesit and Proline tumble dryers.
Please check the suitable model fit list to ensure that this is the correct part for your appliance.
Please note: This part is serial number dependent. Prior to ordering, please ensure that your model and serial number are listed, if you require assistance, please contact our Call Centre with the details from your appliance's data plate.
17 Questions and 18 Answers
ive got a hotpoint tvm570, ive recently replaced the drum bearing due to the noise it was making, that all went well and now theres no noise, the dryer is still drying clothes, and I hovered it all out when I replaced the other part but not the whole dryer seems to be getting really hot when in use?? I have no idea why, so was wondering if anyone had any ideas what this could be thanks.
- Remove the bottom filter (the one you can wash out) and then shine a torch at the back of the housing. There might be a build up of damp fluff that you will have to remove by hand - there should not be any sharp edges but wear a pair of rubber gloves to make sure you do not get cuts or nicks. I removed the LH side of my CTD00P dryer and was able to get my hand in to remove the fluff.
-
Chris at eSpares says...
There is no insulation for the drum and heat will build inside the dryer. However if the air flow is restricted by fluff in the filter or condenser or a blocked vent pipe all the heat and air will be forced into the case from around the drum seal. Check the air ways and pipes are clear and the seals to the drum at the back and front are both in good order. if they are the heat may just be normal.
my tumble dryer is blowing cold air what part do i need the thermostat or the element also me dishwasher is has only cold water what part do i need for that 2 Answers
- Just want to say big thanks saved a single mum a lot if money from Kelly on Anglesey
- Before buying a new tumble dryer element, try resetting the thermostat on the one you have. To do this, unscrew the cover on the back of the tumble dryer, then remove the two screws holding the element to the cover. Look at the "black" (rather than the silver) side of the thermostat. One of the two "buttons" has a small hole in it. Insert a pin in the hole and push down. If you hear a "click", then the thermostat has been reset. Re-attach the element to the cover and the cover to the dryer. The dryer should now blow hot air when operating.
Indesit keeps blowing cold air if I put a big load in it trips the thermostat again which I have to keep resetting and not it just blows cold air wont evan let me reset the thermostat will I need the heating element or a new thermostat ? 1 Answer
-
Parminder at eSpares says...
Please view our advice centre page which will give you more information on this matter, www.espares.co.uk/advice/careandmaintenance/how-to-diagnose-tumble-dryer-drying-and-heating-problems
I have disconnected the heating element and it doesn't Tripp. With the heating element connected but not attached to the back of the dryer I can see the elements heating up and the dryer runs but as soon as I attaché it back to the back of the dryer it trips the electric immediately .
-
Chris at eSpares says...
This is likely to be the problem bit If your model is an IDV75UK you may need another heater Stock Number: ES1523737.
It's a hotpoint 570
-
Chris at eSpares says...
Thump middle front of the top with the palm of your hand to push it back and unlock from the sides.
Will this part fit my appliance?
Check Now
