Tumble Dryer On/Off Push Button Stock Number: ES1591873
Genuine spare part for select models of Beko tumble dryers
Hi, my husband took apart our Beko DCU8230 to replace the on off switch with one purchased from yourselves unfortunately he deleted the picture of the wiring on the front panel. Do you have any information regarding the wiring off this product so that we can put it back together? Thanks
- Hi, on beko dryers behind the on/off switch you should see a brown and orange connector taped together and then a red/yellow connector and a purple/orange/yellow connector, put the brown and orange cable either side of the switch and then put the red and yellow connector under the orange side and the purple/yellow/orange under the brown side, hope this helps.
-
Chris at eSpares says...
The two live connectors (usually brown) go one side of the switch barrier and the two neutral (usually blue) on the other.
The dryer starts then stops almost immediately, sometimes stays on 5 minutes, even 10. Occasionally, it will even goes for 20 minutes, so as you see, it is an intermittent fault. ls this switch likely to cure the problem?
-
Chris at eSpares says...
Unless the switch crackles or shows signs of burning it is unlikely to cause the problem. Check the door switch, power cable to the dryer for signs of damage and burning. If all ok suspect the control panel.
If I need a new part can I fit it myself,if so could you pls explain how
-
Dean at eSpares says...
You will need to gain access to switch by removing the fascia, please see a video on removing the switch on a tumble dryer www.youtube.com/watch?v=KibCEXsesK4 just copy and paste into your browser.
Hi my start pause button has broken. I am using sometjing to hit the little metal bit inside to turn on as my button has came off along with the light. Do i need this part or the light board part? 1 Answer
Can anyone let me know what switch I need that is behind the start/pause button as pushing the button isn't working to well. It's looking like the button is pushed right in but it's not activating the switch. Thank you
-
Chris at eSpares says...
Dismantle the control panel and check if Stock Number: ES1662022 is broken or damaged.
Will this button work for the start pause button? My email is incorrect on this it's linked to my PayPal which isn't correct please can you repsond on the post rather than email
-
Chris at eSpares says...
The likely cause of your problem is Stock Number: ES1662022 you should check if this is broken before by dismantling ordering a part.
I tryed to reconnect the switch and it sparked what dose this mean my dryer won't work now can you send me a picture of what 4 plugs go were and will it have done anymore damage to my machine
-
Chris at eSpares says...
If you connected the wires incorrectly you will have blown the plug fuse and may have damaged the switch. We cannot supply a picture but there are two switches in this device the one side should be brown wires and the other usually blue.
It's the on , off switch for bako DCU 8230
-
Chris at eSpares says...
This switch pushes through the fascia and the 'arrow heads' either side of the button shaft squeeze in and then spring out to hold it in place. to remove the 'tails' of the arrow heads need to be squeezed in to allow them to pass back through the fascia and be removed.
-
Chris at eSpares says...
In order for us to answer your question or source the exact part you require please provide us with the following information: Appliance make, model and serial number of your appliance. For further help visit the "Finding Model Numbers" page on our website here: http://www.espares.co.uk/findingmodelnumbers. Alternatively please copy and paste this link into your web browser.
Hi my dryer is not functioning correctly. When you turn it on the light comes on in the dryer but no lights on the outside and when you turn it on it sound very watery. Not doing anything Can you give me any advise on what the problem could possible be. I think it may be the brain of the dryer. Thanks
-
Chris at eSpares says...
This dryer is a condenser dryer and uses a pump to move water from the reservoir to the collection tank. If it cannot empty this water the machine will not be allowed to start so check the pump and reservoir first before suspecting the control board.
Will this part fit my appliance?
Check Now